Sony HDR-AS30V Camcorder System Software Update Instruction for Mac OS X
Determine if Your Camcorder Needs the Update
This update is only for HDR-AS30V camcorders that currently have firmware version 1.00. If your camcorder firmware version is already Version 2.00, this update is not necessary.
Check the version of your camcorder firmware:
- Power on the camcorder.
- Press the "Next" button to display "Setup", and then press the "Enter" button.
- At the "Setup" screen, press the "NEXT" button. If "FLIP" is displayed, the firmware version is 2.00 and the camcorder does not need this update.
Important Notes
- This utility is only for use with the Sony HDR-AS30V camcorders. Do not install this utility with any other model.
- WARNING!!: This firmware update and any changes incurred by it are permanent. It is not possible to return to a previous firmware version after updating this firmware. By continuing this update process and downloading and updating this firmware, you acknowledge that you are aware and understand that this update cannot be reversed.
- This update process requires the following items for proper updating:
- A computer with:
- CPU: Intel® processor
Note: CoreT Solo and Core Duo processors are not supported. - Available Hard Disk Space: 200 MB or more
- Installed Memory (RAM): 512 MB or more
- A USB port.
- Macintosh® OS X versions 10.5 to 10.8.
- CPU: Intel® processor
- Camcorder power supply:
- This update can only be performed when the remaining battery level has three bars or more. When performing the firmware update, it's recommended to use a fully charged NP-BX1 or NP-FG1 rechargeable battery pack.
WARNING!!: The camcorder may not operate properly if the power is interrupted during the update.
- This update can only be performed when the remaining battery level has three bars or more. When performing the firmware update, it's recommended to use a fully charged NP-BX1 or NP-FG1 rechargeable battery pack.
- USB cable:
- Use only the USB cable supplied with the camcorder.
IMPORTANT: Update functionality is not guaranteed with any other USB cable.
- Use only the USB cable supplied with the camcorder.
- A computer with:
- To ensure that no other program interferes with the installation, save all work and close all other programs. The Taskbar should be clear of applications before proceeding.
- It is highly recommended that you print out these instructions for use as a reference during the installation process.
Prepare the Camcorder for the Firmware Update
- Remove the memory card from the camcorder
- Ensure the camcorder battery is fully charged.
Download and Update the Firmware
- Download the Update_CAMAS30V200.dmg file to a temporary or download directory (please note this directory for reference).
- Go to the directory where the file was downloaded and double-click the Update_CAMAS30V200.dmg.
Note: Do not connect the camera to the computer yet. - Double-click the "Firmware Updater" icon.
- At the Password prompt screen, enter the Name and Password for the administrative account, and then click "OK".
- Ensure the memory card is removed from the camcorder.
- Connect the camcorder to your computer using the supplied USB cable.
Note: "USB Mode" appears on the LCD screen of the camera. - At the "Firmware Updater" window, click "Next".
WARNING!!: Do not power off the camcorder or disconnect the USB cable until the update process is complete. - When the updater recognizes the camcorder connection, the next "Firmware Updater" screen is displayed on the computer, and the camcorder screen displays UPDAT.
- At the "Firmware Updater" window, click "Next".
- When the following screen is displayed, check the version number at the lower left.
If the current version is "1.00", click "Next".
Note: If the current version is "2.00", your camcorder does not need this update. Stop the USB connection and click "Finish". Then power off the camcorder, briefly remove the battery pack, and then power on the camcorder again.
IMPORTANT: Do not disconnect the USB cable from the camcorder or the computer. - On the camcorder, press the ENTER button to reset the camcorder.
After resetting, reconnection of the camcorder is verified, and the following Firmware Updater screen appears. - At the "Firmware Updater" screen, click "Next".
- When the following screen is displayed, click "Run".
Note: The update process takes about ten minutes to complete.
WARNING!!: Do not power off the camcorder or disconnect the USB cable until the update process is complete. - When the following screen is displayed, click "Finish".
- You may now disconnect the USB cable.
- Power off the camcorder and remove the battery pack. Then reconnect the battery pack and power the camcorder back on.
Check the Firmware Version After Updating (optional)
- Power on the camcorder.
- Press the Next button to display "Setup", and then press the "Enter" button.
- At the "Setup" screen, press the "NEXT" button to display "FLIP", this confirms the firmware version is 2.00.
If "FLIP" is displayed, the firmware update was successful.
Note: If "FLIP" is not displayed, please download and install the firmware update again.